CLLT1055/2 Truck Crane

This product has been discontinued and removed from our shelves.

Tips
1. All these parameters are measured under the condition that the truck is static on the solid ground and the platform had been regulated to be at level. The luffing ranges in list are measured under the condition that the boom is lifting the rated load. When we measure the load capacity of the 11m long boom, we make sure all the expansion boom sections had been retracted.
2. The rated lifting capacity includes the weight of host lifting hook of 543kg and the auxiliary lifting hook of 102kg.
When the auxiliary boom is fully extended, the actual lifting capacity of the host lifting boom should be 543kg lower than the rated value.
3. If the host lifting hook is at the end of host boom arm, the actual lifting capacity of auxiliary boom should be 543kg lower than the rated value, and actual lifting capacity of every boom section supported by the boom-end single pulley should be 543kg lower than the rated value and limited within 55000kg.
When the auxiliary lifting hook is on the boom-end single pulley, the actual lifting capacity of each section of the host boom will be 102kg lower than the rated value.
4. Under the condition of not using the fifth supporting leg, the truck crane is forbidden to lift any weight within the 120° sector in front of itself. Only after the fifth supporting leg is mounted can the equipment finish the lifting task 360° all around itself.
5. Please make sure the boom length in the list you refer to is longer than your actual boom length, and arrange the lifting task no heavier than the smallest rate lifting capacity suggested by the list for the sake of safety.
6. At the end of the table are the minimum luffing angles under different boom lengths. It will be risky to lower the boom down below these minimum luffing angles.

Technical Parameters (truck)
Dimensions Length mm 13300
Width mm 2750
Height mm 3685
Wheel base First-Second mm 1450
Second-Third mm 3950
Load capacity Self weight kg 1350
Axle load Fore shaft kg 42200
Aft shaft kg 17000
Kinetic parameters Loaded Model 6BTA5.9-C180
Rated power of engine kW/(r/min) 132/2200
Rated torque of engine N.m/(r/min) 750/1300
Unloaded Model WP10.336
Rated power of engine kW/(r/min) 247/2200
Rated torque of engine N.m/(r/min) 1250/1200~1600
Traveling parameters Maximum driving speed km/h 75
Minimum turning diameter m 24
Minimum ground clearance mm 280
Approach angle ° 17.5
Departure angle ° 13.5
Braking length(30km/h) m 10
Maximum climbing capacity % 32
Fuel consumption per 100 km L 46
Technical Parameter (crane)
Performance parameters Maximum lifting capacity t 55
Minimum rated Luffing range m 3
The platform tail slewing radius mm 3982
Maximum lifting torque Standard kN.m 1764
Supporting leg interval Longitude m 5.5
Transversal m 7.2
Lifting height Standard m 10.94
Longest (host boom) m 40.88
Longest (host and auxiliary boom) m 55.79
Boom length Standard m 11
Longest (host boom) m 41
Longest ( host and auxiliary boom) m 56
Operation parameters Luffing time Full luffing s 65
Extension time Full extension s 115
Maximum slewing speed r/min 1.77
Maximum lifting speed of host boom with single rope (to the third level of height) m/min 115
Auxiliary lifting speed of auxiliary boom with single rope (to the second level of height) m/min 115
Lifting Capacity Parameters (unit: kg)
Luffing range(m) All supporting legs are full extended + fifth supporting leg (360° lifting task)
All supporting legs are full extended (120° front lifting task is forbidden)
Host boom Host boom 41m+Auxiliary boom 9.2m Host boom 41m+Auxiliarty 15m
Boom length (m) Auxiliary boom installation angle
11 18.5 26 33.5 41 15° 30° 15° 30°
3.0 55000









3.5 50500









4.0 43500









5.0 36000 28000 19200







6.0 25600 23500 18300 13800






7.0 20000 19400 17200 13600






8.0 16000 15000 15500 12800 8500





9.0
12000 13200 11700 8200





10.0
9600 11000 10600 7800 3500




11.0
7900 9200 9300 7400 3200




12.0
7200 8000 8200 7000 3000 2400
2400

14.0
5100 6100 6300 6200 2700 2200 2000 2300 1500
16.0

4800 5000 5100 2500 2000 1800 2000 1400
18.0

3400 3900 4000 2200 1800 1700 1800 1300 1000
20.0

2600 3200 3300 2000 1700 1600 1600 1200 1000
22.0


2600 2600 1800 1500 1400 1400 1100 900
24.0


1900 2100 1500 1400 1300 1200 1000 900
26.0


1400 1700 1200 1200 1100 1100 1000 850
28.0



1250 900 1000 900 1000 900 800
30.0




600 700 700 800 800 750
32.0






500 600 700 700
34.0








500 700
Magnification 12 7 5 4 3 1 1
Minimum luffing angle


28° 40° 51° 53°
Luffing curve